Floor-area measurement for quantity surveyors
Area schedules you can defend.
Fabrica is the browser-based measurement workspace for South African QSs. Trace DWG plans at CAD speed, classify every space to the SAPOA method, and export a GCA schedule where every square metre traces back to a line on the drawing.
- No install
- DWG · DXF · vector PDF
- SAPOA 2005 GCA
- Excel schedule export
Product preview: the Fabrica editor traces Office 1.04 on Level 01 of a demo building with the Follow tool, detects the remaining rooms for review, and updates the level totals to a total GCA of 1 982.36 square metres.
The status quo
Most area schedules can’t answer one question: “where did this number come from?”
- 01
Retraced every time the rules change.
Switch from GCA to rentable, or a client asks for a different basis, and the measurement starts again from the drawing.
- 02
Copied from the architect’s drawing.
The printed area goes into the schedule unchecked, and everyone hopes it was right. Nobody measured it.
- 03
Spreadsheets nobody can audit.
Totals with no link back to geometry, author or revision, until a tenant disputes their lease area.
The tracing kernel
Every way to capture an area, and a manual path that always works.
Exact vector tracing on DWG and DXF, built for dense drawings with 100 000+ entities. Detection speeds you up. It never decides for you.
The Follow tool highlights the hovered wall, then traces Office 1.02 corner to corner with snap markers and commits 86.64 square metres.
- Tabcycle candidate
- Entercommit
- Esccancel
- Backspaceundo vertex
- 1–9pick group
- ?all shortcuts
How it works
From drawing to defensible schedule in four steps.
- Step 01
Upload the drawings.
Drop in DWG, DXF or vector PDF. Each floor plan becomes a level, with its layers intact.
- Step 02
Confirm the scale.
Measure one known dimension to lock the scale. Fabrica never assumes one, and an unconfirmed scale blocks approval.
- Step 03
Trace and classify.
Follow walls, capture rooms in one click, or run Detect rooms and review what it finds. Give every space its SAPOA category.
- Step 04
Resolve and export.
Work through the findings, compare each level against the architect’s figure, and export the GCA schedule to Excel.
Built on the SAPOA method
The standard, clause by clause. Not a template.
The GCA profile follows the SAPOA 2005 method for measuring floor areas. Every rule it applies is one you can point to.
- 1.2.1
- Measured at each covered floor level to the external finished surface of permanent external walls.
- 1.3.1
- Voids above an atrium’s lowest level are subtracted.
- 1.2.6
- Balconies, terraces, pools and landscaping are reported separately, never inside GCA. Parking bays are counted.
- Rounding
- Totals round at the end of each sum, not per room, and keep two decimals.
| Level | Total GCA | Retail | Offices | Residential | Circulation | Vert. pen. | BOH | Parking | Residual | Ref. Δ |
|---|---|---|---|---|---|---|---|---|---|---|
| L02 Level 02 | 612.40 | – | – | 498.66 | 58.90 | 24.18 | – | – | 30.66 | +1.20 |
| L01 Level 01 | 648.15 | – | 512.30 | – | 71.08 | 24.18 | 8.42 | – | 32.17 | −3.12, outside the 2 square metre tolerance |
| L00 Ground | 721.81 | 318.40 | – | – | 96.22 | 24.18 | 61.35 | 180.00 | 41.66 | +0.84 |
| Total | 1 982.36 | 318.40 | 512.30 | 498.66 | 226.20 | 72.54 | 69.77 | 180.00 | 104.49 |
- SAPOA 2005 · GCAAvailable
- SAPOA 2005 · Offices rentable areaComing next
- City of Cape TownPlanned
- Retail · Industrial · Residential rentablePlanned
Capture once. Re-derive for any profile.
Traced geometry and classifications are stored apart from the standard that interprets them. Changing the profile recalculates. It never means retracing.
Reconcile, don’t copy
The architect’s number is a reference, not an answer.
Tools that read the area printed on the drawing inherit every mistake on it. Fabrica measures the geometry itself, then checks each level against the architect’s figure. More than 2 m² out, and you see a finding before the client does.
| Level | Reference | Measured | Δ m² |
|---|---|---|---|
| L02 | 611.20 | 612.40 | +1.20 within tolerance |
| L01 | 651.27 | 648.15 | −3.12 outside tolerance |
| L00 | 720.97 | 721.81 | +0.84 within tolerance |
Three modes
Measure it. Present it. Prove it.
Trace, capture and classify. Levels on the left with per-level totals, the selected room on the right.
Show your working
Click any number. See where it came from.
Same inputs, same profile, same answer, every time. Every exported row carries stable IDs back to the geometry and the people who accepted it.
- Source lines and drawing revision for every boundary
- Who accepted each area, and when
- The exact profile version behind every total
- Schedule cellOffices · L01 · 512.30 m²
- Area Dimensions6 accepted · 1.01, 1.02, 1.03, 1.04, 1.05, 1.06
- AreaOffice 1.04 · 86.27 m² · traced with Follow
- SourceA-201 Rev C · layer A-WALL · 14 source segments
- AcceptedT. Mokoena · 14 Oct 2026 · 10:42
- ProfileSAPOA 2005 · GCA v2005.1 · schedule hash 7f3a…c21
Automation that asks, not tells
Let the software find the rooms. You make the calls.
Detect rooms
Finds every enclosed room on a level in one pass. You review, categorise and accept.
- Beta
Suggested categories
Proposes a category for each detected room, such as office, circulation or BOH. Suggestions never apply themselves, and one click undoes them.
Manual always works
If detection misses, or the drawing is unusual, every tool still works by hand. The job never depends on the AI getting it right.
AI features are optional and switched off unless your practice turns them on.
Where Fabrica fits
Deep where it matters. Honest about the rest.
Fabrica does one job: floor-area measurement, done to the standard, with a paper trail. Here is how that compares with the tools QSs usually reach for.
| Capability | Fabrica | AI takeoff platforms | Estimating tools that read printed areas | Desktop takeoff suites |
|---|---|---|---|---|
| SAPOA measurement profiles built in | Yes | No | Partly | No |
| Measures vector geometry rather than reading printed areas | Yes | Yes | No | Yes |
| Checks each level against the architect’s figure | Yes | No | No | No |
| Every number traceable to lines, author and revision | Yes | Partly | Partly | Partly |
| Manual tracing always available | Yes | Partly | Partly | Yes |
| Runs in the browser, no install | Yes | Yes | Yes | No |
| Built for South African practice and standards | Yes | No | Yes | Partly |
| Count takeoff, BoQ and estimatingNot our job. Export the schedule to your estimating tool. | No | Yes | Yes | Yes |
Questions
What QSs ask us first.
Which file formats does Fabrica support?
DWG and DXF are fully supported. Single-sheet vector PDFs are supported with a manually confirmed scale. Scanned or raster drawings aren’t supported: we measure vector geometry, not pixels, so every boundary is exact.
Do I need to install anything?
No. Fabrica runs in a modern desktop browser.
Which standards does it measure to?
SAPOA 2005 Gross Construction Area today, with SAPOA Offices rentable area next. More profiles are on the roadmap, and every schedule records the exact profile version it was calculated under.
Does the AI measure the drawing for me?
No. Detect rooms proposes enclosed rooms, and suggested categories are optional. You accept, correct or ignore them. Every area in a schedule has been accepted by a person.
Can I check another QS’s measurements?
Yes. Every area shows its source lines, author, time and drawing revision, and findings flag overlaps, missing classifications and reference-figure differences.
What do I get out of it?
A GCA schedule in Excel, a room schedule CSV and a presentation plan PDF. Exported rows carry stable IDs back to the geometry and the people who accepted it.
Is it a replacement for my estimating software?
No. Fabrica does floor-area measurement properly and hands a clean schedule to whatever you use next.
How do I get access?
Request a demo. We’ll walk through one of your own drawings with you and set your practice up afterwards.
Request a demo
Bring a drawing. We’ll measure it with you.
Book a 30-minute walkthrough. Send us a DWG from a live project, and we’ll take it from upload to a GCA schedule while you watch.